ADDAC814

We’re pleased to announce our take on matrix mixers, a 6x6 stereo matrix easily expandable to larger configurations.
Matrix mixers may need some time to get used to but they are very much self explanatory: each knob controls the volume of a matrix point routing the respective input to the desired output.
The flexibility of a matrix mixer is far superior to that of a standard mixer. The possibility to route any input to any single or multiple outputs allows for very complex chains, combining parallel and series processing while easily reconfigurable without any extra patching.

All Inputs Left channels are normalled to the Right Inputs.
Blank areas on the left and bottom edges of the panel allow for the user to write all the inputs and outputs sources that each channel is connected to.
Different colored knobs for faster visual recalling: Black for A,C,E Outputs Dark Red for B,D,F Outputs Cream knobs for potential feedback diagonal: 1A, 2B, 3C, 4D, 5E, 6F.
DC coupled circuitry, can be used to mix both audio or cv signals.
Jumpers on the back of both modules allow the user to set each channel independently to Line or Synth Level, making it easier to integrate with external sources, sound processors or guitar pedals.

INTERNAL CONNECTIONS
The control and input modules are connected via a large 34 wire ribbon cable, only the control module needs to be connected to the Busboard.
Extra IDC sockets are used for connecting larger configurations like 12x12 or 18x18.
Other configurations are also possible: 6x12, 12x6, 12x12, etc...
Up to 12x12 all ribbon cables are provided, for larger matrixes custom ones will be necessary, contact us directly if planning to go BIG.

POTENTIOMETERS
Although we're using Thonk's Tall Trimmer Topper for Knobs all potentiometers used have metal shaft and are not plastic trimmer potentiometers.

Tech Specs:
25HP + 8HP (33HP total)
4.5cm deep
140mA +12V
140mA -12V

Note: All specifications and features are subject to change without previous notice.

As a Cheat Sheet, here's what's needed for Matrixes bigger than 6x6.

6x12: 2x 814 [2x Jacks + 2x Controls (1x of these w/o Cream Knobs)]
12x6: 2x Jacks + 1x Controls + 1x Expansion
12x12: 2x 814 (2x Jacks + 2x Controls) + 2x Expansion
12x18: 3x 814 [3x Jacks + 3x Controls (1x of these w/o Cream Knobs)] + 2x Expansion (Custom Cables Required)
18x12: 2x 814 (2x Jacks + 2x Controls) + 1x Jacks + 3x Expansion (Custom Cables Required)
18x18: 3x 814 (3x Jacks + 3x Controls) + 6x Expansion (Custom Cables Required)

When users purchase directly from us, configurations larger than 12x12 get a 7% Discount; larger than 18x18 get a 10% Discount.

For assembling non-standard configurations, you can purchase each module separately:
The Jacks Module costs 90€ (Excl. VAT).
The Controls Module costs 285€ (Excl. VAT).
The Expansion Module costs 275€ (Excl. VAT).

Send us an email if you have questions! 

Music Radar review:
https://www.musicradar.com/music-tech/synths/addac-system-814-6x6-stereo-matrix-mixer-review

Thanks for your interest in the ADDAC814!

To proceed with a direct purchase, you may fill out the form on our Orders Page.

If you want to obtain it through a shop closer to you, this is our Distributors Page.

Product Safety Information

Eurorack Module

Important Safety Information
This Eurorack module is designed for use within standard Eurorack synthesizer systems and is intended for adult users familiar with modular synthesis and electronic equipment.

Please read this safety guide before installation or use.

General Warnings
1. Electrical Hazards:
• Ensure the power supply matches the module’s specified voltage and current ratings (refer to the product manual). Incorrect voltage can damage the module and pose a safety risk.
• Never connect or disconnect the module while the Eurorack system is powered on.
2. Heat Generation:
• The module may generate heat during operation. Ensure proper ventilation within your Eurorack case to prevent overheating.
3. Sharp Edges:
• The module’s faceplate and components may have sharp edges. Handle with care to avoid cuts or scratches.
4. Small Parts:
• Contains small parts that could pose a choking hazard. Keep away from children and pets.
5. Compatibility:
• This module is designed specifically for Eurorack-compatible systems. Connecting it to non-compatible systems may result in damage or malfunction.

Installation and Use
• Mounting: Secure the module properly in the Eurorack case using the provided screws.
• Power Connection: Verify the polarity of the power cable before connecting to avoid damage to the module or power supply. Use only the included or manufacturer-recommended power cable.
• Operational Use: Follow the module's user guide for instructions on operation. Do not exceed the input/output limits specified.
Maintenance and Handling
• Inspection: Regularly check for loose connections or signs of wear.
• Cleaning: Disconnect the module from power before cleaning. Use a dry or lightly damp cloth; avoid using solvents or water directly on the module.
• Repairs: Do not attempt to repair or modify the module yourself. Contact the manufacturer for support.

Environmental Safety
• Dispose of the module, its components, and packaging in accordance with local electronic waste regulations.

Liability Disclaimer
• The manufacturer is not responsible for any injury, damage, or malfunction resulting from improper installation, use, or modification of this product.

Contact Information

For further assistance, contact our support team at:
Addacsystem, Lda.
addac[at]addacsystem[dot]com

The ADDAC814 is also available as a DIY Kit.
The 6x6 configuration (Jacks+Controls modules) costs 370€ (Excl. VAT).

For assembling non-standard configurations, you can purchase each kit separately:
The DIY Kit for the Jacks Module costs 84€ (Excl. VAT).
The DIY Kit for the Controls Module costs 282€ (Excl. VAT).
The DIY Kit for the Expansion Module costs 264€ (Excl. VAT).

To proceed with a direct purchase, you may fill out the form on our Orders Page.

If you want to obtain it through a shop closer to you, this is our Distributors Page.

Here's the detailed step by step Assembly Guide Pdf:
http://media.addacsystem.com/diy_guides/ADDAC814_DIYkit.pdf